ISKYPOOL  โ€ข   DROP STITCH POOLS & OUTDOOR LIVING

ISKYPOOL / Installation & care

Official ISKYPOOL Owner's Manual & Warranty Terms

Official ISKYPOOL manual: setup, 10 PSI, air valve, water chemistry, filtration, storage, PVC repair, safety and warranty terms for manufacturing defects.

Pool scene at sunset.
ISKYPOOL ยท OFFICIAL OWNER'S MANUAL & WARRANTY

Official ISKYPOOL Owner's Manual
& Warranty Terms

This document sets out the installation, safe-use, maintenance, storage and repair requirements for ISKYPOOL swimming pools, together with the manufacturer's warranty terms for manufacturing defects.

Document revision: 2026.07
Last updated: 22 July 2026
The current electronic version is published on the official ISKYPOOL website.
OPERATING PRESSURE
10 PSI
SETUP
Adults only
WARRANTY
Manufacturing defects
TECHNOLOGY
Drop Stitch
Read before filling the pool for the first time
A filled pool contains several tonnes and, in larger models, potentially tens of tonnes of water. Incorrect installation, insufficient pressure, an unsuitable base or misuse can damage the pool and surrounding property.
1. Site preparation

The site must be as level as reasonably possible

A slight surface slope of no more than 2% is permitted. Installation on a surface with a slope greater than 2% is not permitted.

A significant slope creates uneven loading on the pool structure. This can cause localized stress on the material and seams, deformation and micro-damage.

Damage caused by installation on an excessive slope is not a manufacturing defect. However, an unsuitable site does not automatically exclude investigation of a separate manufacturing defect unrelated to the installation conditions.

The base

The base must be firm, stable and capable of carrying the actual pool load. Do not install the pool on loose soil, uncompacted fill, gravel or a surface that may settle noticeably after filling.

Loose sand should not be used simply to level an otherwise unsuitable site. If sand forms part of a properly prepared base, it must be adequately compacted and protected from movement and washout.

Clean the entire footprint

Remove stones, branches, glass, metal, sharp roots and construction debris.

Protective ground layer

A dense protective ground layer suitable for swimming pools is strongly recommended for additional protection of the pool floor.

Punctures, cuts and abrasive damage caused by stones, roots, debris, an unsuitable surface or other external causes are not manufacturing defects.

2. Unpacking and temperature acclimatization

Do not cut deeply into the shipping box

Do not use a utility knife, scissors or another sharp tool in a way that could penetrate the packaging and cut the folded PVC material inside.

A cut caused during unpacking is mechanical damage and is not a manufacturing defect.

After delivery in cold weather

If the pool has been delivered in cold conditions or stored in an unheated area, do not force it open immediately.

Allow the product to warm naturally at room temperature for approximately 12โ€“24 hours. Cold PVC is less flexible and more vulnerable to sharp bending.

3. Air valve and inflation to 10 PSI
ISKYPOOL operating pressure is 10 PSI.

Before the first inflation

With the pool completely deflated, check the air-valve body and, if necessary, tighten it in the correct direction using the supplied valve wrench.

Transportation, vibration and temperature changes can slightly loosen a threaded valve connection. This alone does not indicate a manufacturing defect.

Central valve pin position

During inflation, the central valve pin must be in the closed position. Air should not escape freely from the valve when the compressor hose is disconnected.

Inflation equipment

Use a high-pressure electric SUP compressor capable of reaching the required pressure. Conventional low-pressure blowers can move air quickly but cannot create the required wall rigidity.

After inflation

After reaching 10 PSI, check the valve again. If required, carefully tighten it without excessive force.

Check the valve once more after approximately 2โ€“3 days.

Important warranty information:

The removable air valve is a replaceable service component and is not covered by the voluntary ISKYPOOL manufacturer's warranty unless mandatory law in the country of purchase requires otherwise.

Valve damage caused by incorrect tightening, turning it in the wrong direction, mechanical damage or unauthorized modification is not a manufacturing defect.

A manufacturing defect in the pool body or a non-removable valve mounting area is assessed separately.
4. The first days: pressure and leak checks

Recommended check before first filling

Before the pool is filled for the first time, we recommend inflating it to 10 PSI and leaving it empty for several hours or, where practical, for 12โ€“24 hours.

This allows you to check the valve, pool geometry and any significant air loss before introducing a large volume of water.

Initial pressure reduction

During the first few days after initial inflation, a pressure reduction of approximately 10โ€“15%, and in some cases more, can be normal.

Initial Drop Stitch material adjustment, valve seating and air temperature can all affect pressure readings. Restore the pool to 10 PSI and recheck the valve.

If significant recurring pressure loss continues after approximately two weeks of use, it should no longer be treated as normal initial adjustment. Check the valve and the airtightness of the structure.
5. Filling the pool with water

Never fill the pool if the wall has not been inflated to operating condition, is visibly deformed or cannot maintain its intended geometry.

During the initial filling stage, check that the pool is correctly positioned, the base is not settling and the waterline does not show an obvious tilt.

Water level

For normal use, leaving approximately 5 cm below the upper edge is recommended.

ISKYPOOL pools do not use a mandatory fill line. At the correct operating pressure, water level is not a structural support element for the Drop Stitch wall.

If water accidentally overflows the upper edge, this alone does not damage the pool structure.

Water temperature

Do not heat the water beyond the maximum temperature specified for the relevant pool or heating equipment. Excessive temperature can soften PVC and increase stress on bonded or welded areas.

6. Pool chemicals and water care
Never place granules, tablets or other concentrated dry pool chemicals directly on the PVC surface.

Prolonged direct contact between concentrated chemicals and the pool surface can cause discoloration, chemical damage or localized deterioration of PVC.

Always use swimming-pool chemicals according to the instructions supplied by the chemical manufacturer.

Damage caused by incorrect dosage, direct contact of concentrated chemicals with PVC or unsuitable chemical products is not a manufacturing defect.

7. Filtration, heating and electrical safety

Filtration connections

Use compatible hoses, adapters and seals. Threaded connections must be installed straight and properly sealed.

A small leak at a threaded connection does not by itself indicate a pool-body defect. First check the adapter position, seal and thread sealing.

Electrical equipment

Filtration, heating and other electrical equipment must be connected strictly in accordance with its own manual, grounding requirements and local electrical-safety regulations.

Do not use domestic extension leads, multi-socket adapters or power strips lying on the ground or in areas where they may contact water. A fixed weather-protected grounded outlet with residual-current protection is recommended.

Under ISKYPOOL safety rules, do not use the pool while mains-powered filtration or heating equipment is operating.

8. Safe use

Children

Never leave children in or near the pool without continuous adult supervision.

When the pool is not in use, remove the removable ladder or otherwise prevent unsupervised access to the water.

Diving and jumping

Do not dive, jump into the pool from height or use the pool structure for stunts.

Pets

Animal claws and teeth can mechanically damage PVC. Damage caused by animals is not a manufacturing defect.

Balconies, roofs, decks and raised platforms

Installation on balconies, roofs, raised decks, platforms or other load-bearing structures is permitted only after professional confirmation that the structure can safely support the total actual pool load. ISKYPOOL does not design, calculate or certify the load-bearing capacity of the owner's property.

9. Disassembly, cleaning and long-term storage

Before long-term storage, completely empty the pool, wash it thoroughly and dry it completely.

1. Drain completely
Never leave water inside for winter.
2. Rinse thoroughly
Remove chemicals, body oils, organic contamination and dirt.
3. Dry completely
Pay particular attention to seams and folds.
4. Deflate
A compressor Deflate function makes folding easier.
5. Fold gently
Avoid sharp creases and excessive compression.
6. Store dry
Keep it clean, dry and protected from rodents.
Never fold or store the pool while it is wet.

Mold, fungal growth, persistent odor and material deterioration caused by wet or contaminated storage are not manufacturing defects.

Talc

After complete cleaning and drying, the PVC surface may be lightly dusted with clean talc or a suitable powder without oils. This reduces PVC-to-PVC sticking during storage. Talc is also used for this purpose in ISKYPOOL production.

Storage below freezing

A clean, dry and folded pool may be stored in an unheated space. However, frozen PVC becomes significantly less flexible.

Do not move, unfold or sharply bend the pool while frozen, and do not place heavy objects on top of it. Allow the material to warm naturally before handling.

10. DIY PVC repair

PVC is a repairable material. Many localized punctures, cuts and surface damages can be repaired by the owner.

General repair procedure:

1. Locate the air leak using a soap solution.
2. Mark the damaged area and fully deflate the pool.
3. Prepare a PVC patch with rounded corners, extending approximately 2โ€“3 cm beyond the damaged area.
4. Clean and degrease both surfaces with a product compatible with the PVC and selected adhesive.
5. Use a suitable polyurethane or other professional PVC adhesive strictly according to its instructions.
6. If the selected adhesive requires heat activation, apply heat only as specified by the adhesive manufacturer.
7. Press or roll the patch firmly from the center toward the edges.
8. Allow the required curing time before reinflation.

Do not use an aggressive solvent simply because it is available. The surface-preparation product must be compatible with the specific PVC and adhesive.

Repairing accidental damage does not by itself remove the possibility of investigating a separate manufacturing defect unrelated to that repair.

11. What does the ISKYPOOL warranty cover?

The ISKYPOOL manufacturer's warranty applies to confirmed manufacturing defects in materials and workmanship.

Manufacturing defect in pool material
Manufacturing defect in a factory seam or bonded joint
Manufacturing defect in the Drop Stitch structure
Other confirmed manufacturing defect

Applicable claim periods are determined by the conditions of sale and mandatory law in the relevant market.

12. What is not a manufacturing defect?

The manufacturer's warranty does not cover damage or changes caused by use, external impact, normal wear or failure to follow the instructions.

Punctures, cuts and mechanical damage
Damage from stones, roots, gravel and abrasion
Damage caused by a slope greater than 2%
Filling a pool that is not adequately inflated
Exceeding permitted pressure
Damage caused by animals
Chemical damage to PVC
Mold or damage caused by wet storage
Damage caused by handling frozen PVC
Freezing of water left inside the pool
Unauthorized structural modification
Additional holes or valve modifications
Damage caused by unsuitable adhesives or solvents
Direct burial and surrounding-soil pressure
Groundwater or inadequate drainage
Normal wear from use

An exclusion applies when the relevant misuse or external factor caused the particular damage being claimed.

13. How to make a warranty or support request

If you discover a problem, do not try to determine its cause solely from appearance. Contact the authorized seller or ISKYPOOL support.

For faster diagnosis, provide:

โ€ข proof of purchase;
โ€ข pool model;
โ€ข serial number;
โ€ข a full-view photo;
โ€ข photographs or video of the suspected defect;
โ€ข a brief explanation of when and under what conditions the issue was discovered.

ISKYPOOL or the authorized seller may request additional photographs, video, measurements, diagnostic actions or inspection of the product in order to determine the cause of damage.

Do not discard the product or destroy the suspected damaged area before the claim is completed unless support specifically authorizes it.

14. Current electronic version and QR code

Before ISKYPOOL products are dispatched, a QR code linking to the official electronic manual is placed on the product, packaging or accompanying material.

ISKYPOOL conducts endurance testing, analyzes real-world operating experience and improves its product-use recommendations. The electronic manual may therefore be updated.

The currently published revision replaces previous operating recommendations from the date it is published.

The purchaser must review the current electronic manual before using the product and take into account subsequent updates relating to safety, maintenance and operation.

Updates to this manual do not restrict mandatory consumer rights that cannot legally be limited by the manufacturer or seller under the applicable law of the relevant country.

15. Below-ground installation

ISKYPOOL is primarily designed for above-ground use. Direct burial of the pool in soil is not recommended by the manufacturer.

Damage resulting from soil pressure, groundwater, inadequate drainage, abrasive soil contact, seasonal soil movement or other unsuitable below-ground installation is not a manufacturing defect.

Read the site preparation guide
16. Well water and water discoloration

Water from wells can contain elevated levels of iron, copper, manganese and other dissolved minerals.

Adding chlorine or another oxidizing treatment may rapidly change the color of such water. It can become brown, rusty, greenish or dark.

This type of water discoloration does not by itself indicate dye or contaminants being released from the pool and is not a defect in the PVC material.

17. Modifications, extreme tests and misuse

Do not cut additional openings, modify valves, alter the pool structure or attach third-party accessories using unknown or incompatible adhesives.

Unapproved chemical products can damage PVC, cause localized brittleness, deformation or loss of airtightness.

Social-media videos showing ice being broken with axes inside pools, jumping on frozen PVC, impacts with sharp objects or other extreme behavior do not represent approved ISKYPOOL use.

Damage caused by such actions is not a manufacturing defect.
THE CORE ISKYPOOL WARRANTY PRINCIPLE
Manufacturing defect: our responsibility.
Damage caused by use: not a manufacturing defect.

If the cause of the damage is unclear, do not draw a conclusion in advance. Send photographs, a video and the serial number to official ISKYPOOL support for diagnosis.

Need step-by-step video instructions?

Pool installation, air valve, filtration, heat pump and other equipment.

ISKYPOOL video guides

โ† Back to all guides